-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)13. Report13.1 Report the following information:13.1.1 Wear scar diameter to the nearest 0.01 mm (from 12.2),13.1.2 Description of the wear scar area, and13.1.3 Deviations ...
-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)11. Procedure11.1 The procedure for testing using the semi automatic method is described in Annex A1.11.2 The procedure for testing using the fully automatic method ...
-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)9. Preparation of Apparatus9.1 Use the following procedures, where applicable:Annex A1 for the semi-automatic method.Annex A2 for the fully automatic method.10. Calibration ...
-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)6. Apparatus6.1 For details of the Ball-On-Cylinder Lubricity Evaluator (BOCLE), apparatus required for each method see: Annex A1 for the semi-automatic method, Annex ...
-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)4. Summary of Test Method4.1 The fluid under test is placed in a test reservoir in which atmospheric air is maintained at 10 % relative humidity. A non-rotating steel ...
-
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine
ASTM D5001 Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)1. Scope1.1 This test method covers assessment of the wear aspects of the boundary lubrication properties of aviation turbine fuels on rubbing steel surfaces.1.1.1 ...
-
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking F
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking Fluids9. Report9.1 Report as "breakpoint" the weakest concentration tested that left no rust stain on the filter paper.9.2 Report the estimated percentage of rust stain on the filter paper for each concentration tested.10. ...
-
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking F
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking Fluids8. Procedure8.1 Make the test in a room free from corrosive fumes, away from direct sunlight, and a room temperature of 20 °C to 25 °C.8.2 Sieve the cast iron chips (6.1) on the 18 mesh screen (5.11), rejecting the ...
-
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking F
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking Fluids5. Apparatus5.1 Disposable Petri Dishes, 35 mm by 10 mm plastic, with lids.5.2 Glass-Fiber Filter Paper, 1.5 µm particle retention rating, 3.2 cm diameter.5.3 Glass Stirring Rod.5.4 Spatula.5.5 Pipettes, 5 mL.5.6 Glass ...
-
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking F
ASTM D4627 Test Method for Iron Chip Corrosion for Water-Miscible Metalworking Fluids3. Summary of Test Method3.1 Cast iron chips are placed in a petri dish containing a filter paper and diluted metalworking fluid. The dish is covered and allowed to stand overnight. The amount of rust stain on the filter ...
