-
ASTM D6823 Specification for Commercial Boiler Fuels with Used Lubricating Oils
ASTM D6823 Specification for Commercial Boiler Fuels with Used Lubricating Oils4. Significance and Use4.1 The intention of this specification is to cover fuel oil used in industrial equipment and commercial boilers as stated in the Scope section. The use of used lube oil in marine and industrial diesel ...
-
ASTM D6823 Specification for Commercial Boiler Fuels with Used Lubricating Oils
ASTM D6823 Specification for Commercial Boiler Fuels with Used Lubricating Oils1. Scope1.1 This specification covers four grades of fuel oil made of at least 25 % used lubricating oils. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment and commercial ...
-
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air7. Interpretation of Results7.1 Any indication of oil discoloration on the collector shall be cause for rejection of the compressed air for use in abrasive blast cleaning, air blast cleaning, and coating application operations.7.2 ...
-
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air6. Procedure6.1 Use either the absorbent or nonabsorbent collector.6.2 Position the collector within 24 in. of the air-discharge point, centered in the air stream.6.3 Adjust air discharge so that the collector remains intact ...
-
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air3. Apparatus and Materials3.1 Absorbent Collector, such as white absorbent paper or cloth and rigid backing for mounting absorbent collector, or3.2 Nonabsorbent Collector, such as rigid transparent plastic, approximately 1/4 ...
-
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air2. Significance and Use2.1 Clean compressed air is required to prevent contamination of coating materials and surfaces being prepared for coating. This test method is a visual examination technique for determining oil or water ...
-
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air1. Scope1.1 This test method is used to determine the presence of oil or water in compressed air used for abrasive blast cleaning, air blast cleaning, and coating application operations.1.2 This standard does not purport to ...
-
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivativ
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivatives9. Calculation and Report9.1 Calculate the total iodine value, T, as follows:T = [(B - V) x N x 12.69]/Swhere:B = Na2S2O3 solution required for titration of the blank, mL,V = Na2S2O3 solution required for titration of the ...
-
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivativ
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivatives8. Procedure8.1 To a 250-mL glass-stoppered iodine flask (Note 2), add 5 mL of solvent. In this dissolve the specimen, weighed to 0.1 mg, using the weight of specimen prescribed in Table 1.NOTE 6 - The specimen weight is ...
-
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivativ
ASTM D1541 Test Method for Total Iodine Value of Drying Oils and Their Derivatives5. Apparatus5.1 Iodine Flasks, glass-stoppered, of 250-mL capacity.NOTE 2 - The test may be run either in a photographic-type darkroom under red safelight illumination5 or in a darkened laboratory in which the light intensity ...
