Home > Classroom
- ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware6. Apparatus6.1 Container - A 500-mL graduated container of heat-resistant glass, having a diameter of 45 to 50 mm and a length of 380 mm.6.2 Temperature Bath - Aheat resistant glass container large enough to permit immersion ...
- ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware4. Summary of Test Method4.1 A solution of coolant and ASTM Type II water is blown with air at a constant rate for 5 min, while maintained at a constant temperature of 88 +/- 1°C (190 +/- 2°F) by means of a suitable temperature ...
- ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware ASTM D1881 Test Method for Foaming Tendencies of Engine Coolants in Glassware1. Scope1.1 This test method covers a simple glassware test for evaluating the tendency of engine coolants to foam under laboratory-controlled-conditions of aeration and temperature.1.2 This standard does not purport to address ...
- ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organi ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles8. Report8.1 The report shall include the following:8.1.1 Product and concentration tested.8.1.2 Coating systems employed.8.1.3 Type and appearance of the effect obtained on the test panel, ...
- ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organi ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles7. Procedure7.1 Conduct the test at 25 +/- 5 °C without humidity control.7.2 Select a test panel prepared in accordance with Section 5. Place sufficient test solution on the surface of the ...
- ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organi ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles5. Materials5.1 Test Panels - Steel panels, approximately 100 by 150 mm (4 by 6 in.) shall be prepared in accordance with the Methods of Preparation of Practice D609. The surface of the test ...
- ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organi ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles3. Summary of Test Method3.1 Concentrated or diluted cooling system chemical solutions are brought into contact with organic finishes typical of those used on automobiles for 1 h at room ...
- ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organi ASTM D1882 Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles1. Scope1.1 This test method determines the effect ofcooling system chemical solutions on organic finishes used on motor vehicles. Cooling system chemicals include: coolants or corrosion ...
- ASTM D3634 Standard Test Method for Trace Chloride Ion in Engine Coolants ASTM D3634 Standard Test Method for Trace Chloride Ion in Engine Coolants12. Report12.1 Report the chloride content of the engine coolant to the nearest unit.13. Precision and Bias13.1 The reproducibility of the chloride ion determination by this test method is 5 ppm in the range from 5 to 200 ppm.13.2 ...
- ASTM D3634 Standard Test Method for Trace Chloride Ion in Engine Coolants ASTM D3634 Standard Test Method for Trace Chloride Ion in Engine Coolants10. Procedure10.1 To a 250-mL Erlenmeyer flask add 50 +/- 0.1 g of engine coolant and approximately 30 mL of water. Make the solution strongly alkaline by the addition of 5 mL of 20 mass % aqueous NaOH solution. Add 5 mL of 30 mass ...