Home > Classroom

  • ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester9. Preparation of Apparatus9.1 Place the apparatus on a level, stable surface. Unless tests are made in a draft-free area, surround the tester on three sides with a draft shield (see 6.3) for protection. Do not rely on tests made ...
  • ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester6. Apparatus6.1 Test Cup and Cover Assembly - The essential dimensions and requirements of the apparatus are shown in Fig. A1.1 and Table A1.1 of Annex A1. The apparatus and accessories are described in detail in Annex A1. The temperature ...
  • ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester4. Summary of Test Methods4.1 Method A - Flash/No Flash Test - A test specimen is introduced, by a syringe, into the test cup of the selected apparatus that is set and maintained at the specified temperature. After a specific time ...
  • ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester ASTM D3828 Test Methods for Flash Point by Small Scale Closed Cup Tester1. Scope1.1 These test methods cover procedures for flash point tests, within the range of -30 to 300°C, of petroleum products and biodiesel liquid fuels, using a small scale closed cup tester. The procedures may be used to determine, ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids9. Calculation and Report9.1 Calculate and report the oil output from the mist generator after break-in in grams per hour as follows:where:W1 = weight of the mist generator at the start of the test, g, andW2 = weight of the mist generator ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids8. Procedure8.1 Break-In Period:8.1.1 Charge the mist generator with 4 ± 0.1 L of test oil. Assemble the test apparatus.8.1.2 Turn the oil flow adjusting screw clockwise to a fully closed position and then open the screw by turning it ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids7. Preparation of Apparatus7.1 Thorough cleaning of the apparatus with solvent is required prior to initiating a test on a new oil. For a duplicate test on the same oil, the mist generator should be thoroughly drained but the apparatus ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids5. Apparatus5.1 The basic system consists of the following:5.1.1 Oil Mist Generator, with special ASTM-ASLE mist head assembly.5.1.2 Air Temperature Regulator.5.1.3 Mist Distribution Manifold, as shown in Fig. 1.5.1.4 Mist Reclassifier ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids3. Summary of Test Method3.1 The mist generator is charged with oil and installed in the mist system. The unit is operated for 19 h; the mist generator, line condensate bottles, and reclassified oil collector are weighed before and after ...
  • ASTM D3705 Test Method for Misting Properties of Lubricating Fluids ASTM D3705 Test Method for Misting Properties of Lubricating Fluids1. Scope1.1 This test method covers the determination of the misting characteristics of lubricating fluids.NOTE 1 - This test method should not be used to evaluate fluids containing solid additives such as graphite.1.2 This standard does ...