-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine12. Report12.1 Report the following information:12.1.1 Reporting Test Results - For reference oil tests, the standardized report form set and data dictionary for reporting the test results and for summarizing the ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine11. Laboratory and Engine Test Stand Calibration/Non-Reference Requirements11.1 Calibration Frequency - To maintain test consistency and severity levels, engine test stand calibration is required at regular intervals. ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine10. Inspection of Engine, Fuel, and Oil10.1 Pretest Measurements:10.1.1 Pistons - No piston measurements are required.10.1.2 Cylinder Sleeves Inside Diameter Surface Finish - Measurement is to be an average of four ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine9. Procedure9.1 Pretest Procedure:9.1.1 Initial Oil Fill for Pretest Break-In - The initial oil fill is 39.2 kg (86.4 lb) of test oil: 22.9 kg (50.4 lb) for the pan, 3.3 kg (7.2 lb) for the filters, 1.6 kg (3.6 lb) ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine8. Preparation of Apparatus at Rebuild8.1 Cleaning of Parts:8.1.1 Engine Block - Thoroughly spray the engine with solvent (see 7.4) to remove any oil remaining from the previous test, and air dry.8.1.2 Rocker Covers ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine6. Apparatus6.1 General Description:6.1.1 The test engine is a Mack E7-350 electronically governed engine, P/N 11GBA78786 (see Annex A3). It is an open-chamber, in-line, six-cylinder, four-stroke, turbocharged, charge ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine4. Summary of Test Method4.1 The test operation involves use of a Mack E7-350 V-MAC II diesel engine with a warm-up and a 1 h break-in, followed by a two-phase test consisting of 75 h at 1800 r/min and 425 h at 1250 ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine1. Scope1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including lead corrosion and wear of piston rings and cylinder liners. This test method ...
-
ASTM D7583 Standard Test Method for John Deere Coolant Cavitation Test
ASTM D7583 Standard Test Method for John Deere Coolant Cavitation Test12. Report12.1 Report Forms - For reference coolant tests the standardized report form set and data dictionary for reporting test results and for summarizing the operational data are required. The report forms and data dictionary are ...
-
ASTM D7583 Standard Test Method for John Deere Coolant Cavitation Test
ASTM D7583 Standard Test Method for John Deere Coolant Cavitation Test10. Procedure10.1 Engine Installation and Stand Connections - Install the test engine on the stand and connect the engine to the stand support equipment.NOTE 2 - A final check of valve and injector settings is recommended at this time.10.2 ...
