-
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Str
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine6. Apparatus6.1 Test Engine - A single-cylinder Caterpillar diesel oil test engine having a 2.2 L (134.1 in.) displacement is required. Bore and stroke are 13.0 ...
-
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Str
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine4. Summary of Test Method4.1 Prior to each test run, the power section of the engine (excluding piston assembly) is completely disassembled, solvent-cleaned, measured, ...
-
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Str
ASTM D6618 Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine1. Scope1.1 This test method covers a four-stroke cycle diesel engine test procedure for evaluating engine oils for certain high-temperature performance characteristics, ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine12. Report12.1 Report the following information:12.1.1 Reporting Test Results - For reference oil tests, the standardized report form set and data dictionary for reporting the test results and for summarizing the ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine11. Laboratory and Engine Test Stand Calibration/Non-Reference Requirements11.1 Calibration Frequency - To maintain test consistency and severity levels, engine test stand calibration is required at regular intervals. ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine10. Inspection of Engine, Fuel, and Oil10.1 Pretest Measurements:10.1.1 Pistons - No piston measurements are required.10.1.2 Cylinder Sleeves Inside Diameter Surface Finish - Measurement is to be an average of four ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine9. Procedure9.1 Pretest Procedure:9.1.1 Initial Oil Fill for Pretest Break-In - The initial oil fill is 39.2 kg (86.4 lb) of test oil: 22.9 kg (50.4 lb) for the pan, 3.3 kg (7.2 lb) for the filters, 1.6 kg (3.6 lb) ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine8. Preparation of Apparatus at Rebuild8.1 Cleaning of Parts:8.1.1 Engine Block - Thoroughly spray the engine with solvent (see 7.4) to remove any oil remaining from the previous test, and air dry.8.1.2 Rocker Covers ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine6. Apparatus6.1 General Description:6.1.1 The test engine is a Mack E7-350 electronically governed engine, P/N 11GBA78786 (see Annex A3). It is an open-chamber, in-line, six-cylinder, four-stroke, turbocharged, charge ...
-
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Dies
ASTM D6483 Standard Test Method for Evaluation of Diesel Engine Oils in T-9 Diesel Engine4. Summary of Test Method4.1 The test operation involves use of a Mack E7-350 V-MAC II diesel engine with a warm-up and a 1 h break-in, followed by a two-phase test consisting of 75 h at 1800 r/min and 425 h at 1250 ...
